MIC2164YMM
Or copy the link below:
- Mfr.Part #
- MIC2164YMM
- Manufacturer
- Microchip Technology
- Package / Case
- Datasheet
- Download
- Description
- IC REG CTRLR BUCK 10MSOP
- Stock
- 65
- In Stock ：
- 65
Request A Quote(RFQ)
- * Fullname:
- * Company:
- * E-Mail:
- Phone:
- Comment:
- * Quantity:
- Manufacturer :
- Microchip Technology
- Product Category :
- DC DC Switching Controllers
- Product Status :
- Active
- Topology :
- Buck
- Mounting Type :
- Surface Mount
- Frequency - Switching :
- 300kHz
- Function :
- Step-Down
- Voltage - Supply (Vcc/Vdd) :
- 3V ~ 28V
- Supplier Device Package :
- 10-MSOP
- Synchronous Rectifier :
- Yes
- Control Features :
- Enable
- Operating Temperature :
- -40°C ~ 125°C (TJ)
- Output Phases :
- 1
- Clock Sync :
- No
- Number of Outputs :
- 1
- Output Configuration :
- Positive
- Output Type :
- Transistor Driver
- Serial Interfaces :
- -
- Duty Cycle (Max) :
- 87%
- Datasheets
- MIC2164YMM
3V~28V 10-Pin MIC2164 DC to DC converter IC SWITCHING CONTROLLER 1 Outputs 300kHz Transistor Driver
MIC2164YMM Overview
Capsuled in the 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) package, the switching controller can be used for a wide range of applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. PMIC packaging is solid with a Tube enclosure. A total of Transistor Driver dc switching's outputs can be handled by it. Voltages 3V~28V are the dc control's supply voltage and operating voltage, respectively. Work well in dc switchers with a -40°C~125°C TJ. Using this switching controller, it is possible to switch at 300kHz. A generalization of dc dc regulator can be made using Surface Mount. To ensure efficient switching, this dcdc regulator features a Enable. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. A switching converters's terminal (s) sits at the DUAL position. The control methods that these dc dc converter ics use include HYSTERETIC CURRENT MODE. DC switcher's voltage input is 5 V. You can find other relevant dc to dc converter ics by searching "MIC2164". Pins number 10 of switching converter in total. Specially, switching converter corresponds to type PMIC - Power Management ICs. Test statistics indicate DC regulator outputs 5.5V voltage. In most cases, the dc dc regulator's output current is 25A. This information should be noted when you begin working with the component. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 87 % during power-up and power-down. The Surface Mount makes DC switcher suitable for most applications and prototypes. Switching controller operates at 300kHz Hz. The value of DC to DC voltage regulator is set at ALSO OPERATES IN ADJUSTABLE MODE FROM 0.8 TO 5.5V in order to fulfill the requirements more effectively. Users should apply 3, 28 V to operate the voltage regulator dc to dc safely and reliably. At least -40°C°C is recommended. At125°C, dc regulator should run. Basically, it's a dc to dc voltage regulator from the Hyper Speed Control® series. 1 functions are available in total for the switch converters. We design voltage regulators switchings with 10 pins. The maximum input voltage of dc switcher is 5.5V, so users should limit their voltage accordingly. A 10-MSOP would be the supplier dc dc controller package for this part. Voltage 3V is needed for the supply. The datasheet indicates that the switching converter can output 5.5V volts at its maximum. A current of 3mA is supplied to it. The phase of this controller is 1. In this switching controller, 375 kHz represents the top frequency at which it can switch. Voltage maximum is rated 28V. Continually operating at more than 3mA may cause malfunctions and damage to the component. The temperature can go as low as 125C degrees Celsius. At 1 MHz, this controller will mostly work as expected. The bottom temperature of the dc to dc voltage regulator should be -40C.
MIC2164YMM Features
Transistor Driver Outputs
Switching Frequency: 300kHz
Enable
HYSTERETIC CURRENT MODE
Max Duty Cycle: 87 %
Frequency: 300kHz
ALSO OPERATES IN ADJUSTABLE MODE FROM 0.8 TO 5.5V
Switching Frequency: 1 MHz
MIC2164YMM Applications
There are a lot of Microchip Technology
MIC2164YMM DC to DC converter applications.
- Various precision measuring instruments
- Various precision measuring detectors
- Flaw detection equipment
- Balance equipment
- Industrial robots
- Industrial controllers
- Die casting equipment
- Injection molding machinery
- Various CNC machine tools
- Machining centers
You may place an order without registering to VESS Electronics. We strongly recommend that you log in before purchasing as you can track your order at any time.
RFQ (Request for Quotations)It is recommended to send RFQ to get the latest prices and stock availability about the part.Our sales will reply to your inquiry within 24 hours.
Payment MethodFor your convenience, we accept multiple payment methods in USD, Such as:PayPal, Credit Card, and wire transfer.
IMPORTANT NOTICEYou may place an order without registering to 1. You'll receive an order confirmations by e-mail soon . (Please remember to check the spam box if you didn't hear from us). 2. Since stock availability and prices may change at any time, the sales will reconfirm the order details and update you at soonest time.
Most of our products are shipped via FEDEX,DHL,UPS and SF EXPRESS...
Shipping CostShipping Cost starts at $40, but some countries will exceed $40. For example (South Africa, Brazil, India, Pakistan, Israel, etc.).If customer have shipping account, we can make shipment under customer’s shipping account with freight collect directly.
The basic freight (for package ≤0.5 KG ) depends on the time zones and countries
Once the goods are shipped, estimated delivery time depends on the shipping methods you chose. You can track it by the tracking no.
