MCP1651S-E/MS
Or copy the link below:
- Mfr.Part #
- MCP1651S-E/MS
- Manufacturer
- Microchip Technology
- Package / Case
- Datasheet
- Download
- Description
- IC REG CTRLR MULT TOPOLOGY 8MSOP
- Stock
- 242
- In Stock ：
- 242
Request A Quote(RFQ)
- * Fullname:
- * Company:
- * E-Mail:
- Phone:
- Comment:
- * Quantity:
- Manufacturer :
- Microchip Technology
- Product Category :
- DC DC Switching Controllers
- Synchronous Rectifier :
- No
- Control Features :
- Current Limit, Enable, Low Battery, Power Good
- Number of Outputs :
- 1
- Product Status :
- Active
- Frequency - Switching :
- 750kHz
- Function :
- Step-Up, Step-Up/Step-Down
- Topology :
- Boost, Flyback, SEPIC
- Output Type :
- Transistor Driver
- Supplier Device Package :
- 8-MSOP
- Serial Interfaces :
- -
- Output Phases :
- 1
- Operating Temperature :
- -40°C ~ 125°C (TJ)
- Mounting Type :
- Surface Mount
- Voltage - Supply (Vcc/Vdd) :
- 2.7V ~ 5.5V
- Clock Sync :
- No
- Output Configuration :
- Positive
- Duty Cycle (Max) :
- 80%
- Datasheets
- MCP1651S-E/MS
8 Terminals 2.7V~5.5V 8-Pin MCP1651 DC to DC converter IC SWITCHING CONTROLLER 1 Outputs 750kHz Transistor Driver
MCP1651S-E/MS Overview
The switching controller fits in the 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package and is ideal for most applications. dc motor controller is suitable for 1 output generation. Packaged in solid enclosures, this pmic has a Tube rating. There are Transistor Driver dc switching's output (s) that it can handle. A 2.7V~5.5V voltage is supplied to the dc control and used for operating it. Suitable for work in a -40°C~125°C TJ dc switcher. With this switching controller, you can switch at 750kHz. The Surface Mount makes it ideal for general dc dc regulator. Featured in the dcdc regulator is Current Limit, Enable, Low Battery, Power Good which allows efficient switching control. Thare switch converters are connected to an analog integrated circuit (IC) of type SWITCHING CONTROLLER. There are a terminal (s) on the switching converters that are designed at DUAL. 8 terminations with various dc switching's functions. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. The DC switcher's nominal voltage is 3.3V. Other relevant dc to dc converter ics will be returned if you search "MCP1651". Total pins of switching converter are 8. A 100V voltage of DC regulator was detected in the test statistics. If you start a project, note down the dc dc regulator's usual output current of 100mA. The duty cycle of the voltage regulator dc to dc can be set to 88 % on power-up or power-down to ensure reliability. Having a Surface Mount makes DC switcher suitable for most application and prototype designs. There is a maximum frequency of 850kHz for this dc regulators. To operate the voltage regulator dc to dc safely and reliably, users should apply 5.5 V. Whenever the current value is 1 A, switching converter outputs the highest possible value. At -40 °C and above, dc regulator should be kept. At a temperature around 125 °C degrees Celsius, dc regulator should be running. It belongs to the dc to dc voltage regulator series --. Overall, the switch converters contains 1 function(s). Voltage regulators switching is designed with 8 pins. The maximum input voltage of this dc switcher is 5.5V, so users must limit the voltage accordingly. Its supplier dc dc controller package is 8-MSOP. A voltage of 2V must be present in the supply. A dc switcher can only produce an output current of 100mA. A datasheet states that the switching converter can output 12V volts at its maximum. There is a 120μA volt supply current. Lowest voltage output of the voltage controller must be greater than 3.3V. 850 kHz is the highest frequency at which the switching controller can switch. When it comes to maximum supply voltage, switching voltage regulators is rated 5.5 V. The nominal current supply of this the controllers dc is 120μA. When this switching controller is running at frequency 750 kHz, it can perform well in most cases.
MCP1651S-E/MS Features
Transistor Driver Outputs
Switching Frequency: 750kHz
Current Limit, Enable, Low Battery, Power Good
PULSE WIDTH MODULATION
Max Duty Cycle: 88 %
Switching Frequency: 750 kHz
MCP1651S-E/MS Applications
There are a lot of Microchip Technology
MCP1651S-E/MS DC to DC converter applications.
- CMM
- Various precision measuring instruments
- Various precision measuring detectors
- Flaw detection equipment
- Balance equipment
- Industrial robots
- Industrial controllers
- Die casting equipment
- Injection molding machinery
- Various CNC machine tools
You may place an order without registering to VESS Electronics. We strongly recommend that you log in before purchasing as you can track your order at any time.
RFQ (Request for Quotations)It is recommended to send RFQ to get the latest prices and stock availability about the part.Our sales will reply to your inquiry within 24 hours.
Payment MethodFor your convenience, we accept multiple payment methods in USD, Such as:PayPal, Credit Card, and wire transfer.
IMPORTANT NOTICEYou may place an order without registering to 1. You'll receive an order confirmations by e-mail soon . (Please remember to check the spam box if you didn't hear from us). 2. Since stock availability and prices may change at any time, the sales will reconfirm the order details and update you at soonest time.
Most of our products are shipped via FEDEX,DHL,UPS and SF EXPRESS...
Shipping CostShipping Cost starts at $40, but some countries will exceed $40. For example (South Africa, Brazil, India, Pakistan, Israel, etc.).If customer have shipping account, we can make shipment under customer’s shipping account with freight collect directly.
The basic freight (for package ≤0.5 KG ) depends on the time zones and countries
Once the goods are shipped, estimated delivery time depends on the shipping methods you chose. You can track it by the tracking no.
