MCP1651R-E/MS
Or copy the link below:
- Mfr.Part #
- MCP1651R-E/MS
- Manufacturer
- Microchip Technology
- Package / Case
- Datasheet
- Download
- Description
- IC REG CTRLR MULT TOPOLOGY 8MSOP
- Stock
- 69
- In Stock ：
- 69
Request A Quote(RFQ)
- * Fullname:
- * Company:
- * E-Mail:
- Phone:
- Comment:
- * Quantity:
- Manufacturer :
- Microchip Technology
- Product Category :
- DC DC Switching Controllers
- Output Type :
- Transistor Driver
- Output Phases :
- 1
- Synchronous Rectifier :
- No
- Voltage - Supply (Vcc/Vdd) :
- 2.7V ~ 5.5V
- Product Status :
- Active
- Serial Interfaces :
- -
- Mounting Type :
- Surface Mount
- Operating Temperature :
- -40°C ~ 125°C (TJ)
- Number of Outputs :
- 1
- Control Features :
- Current Limit, Enable, Low Battery, Power Good
- Function :
- Step-Up, Step-Up/Step-Down
- Output Configuration :
- Positive
- Clock Sync :
- No
- Duty Cycle (Max) :
- 80%
- Topology :
- Boost, Flyback, SEPIC
- Frequency - Switching :
- 750kHz
- Supplier Device Package :
- 8-MSOP
- Datasheets
- MCP1651R-E/MS
8 Terminals 2.7V~5.5V 8-Pin MCP1651 DC to DC converter IC SWITCHING CONTROLLER 1 Outputs 750kHz Transistor Driver
MCP1651R-E/MS Overview
Capsuled in the 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package, the switching controller can be used for a wide range of applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. PMIC packaging is solid with a Tube enclosure. A total of Transistor Driver dc switching's outputs can be handled by it. Voltages 2.7V~5.5V are the dc control's supply voltage and operating voltage, respectively. Work well in dc switchers with a -40°C~125°C TJ. Using this switching controller, it is possible to switch at 750kHz. A generalization of dc dc regulator can be made using Surface Mount. To ensure efficient switching, this dcdc regulator features a Current Limit, Enable, Low Battery, Power Good. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. A switching converters's terminal (s) sits at the DUAL position. A variety of dc switching's functions can be performed on 8 terminations. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's voltage input is 3.3V. You can find other relevant dc to dc converter ics by searching "MCP1651". Pins number 8 of switching converter in total. Test statistics indicate DC regulator outputs 100V voltage. In most cases, the dc dc regulator's output current is 100 mA. This information should be noted when you begin working with the component. As a result of this, the maximum duty cycle of the voltage regulator dc to dc must remain 88 % during power-up and power-down. The Surface Mount makes DC switcher suitable for most applications and prototypes. It is estimated that this dc regulatorhas a maximum frequency of 850 kHz. Switching controller operates at 750kHz Hz. Users should apply 5.5 V to operate the voltage regulator dc to dc safely and reliably. A maximum value of 1 A is output for current. At least -40 °C°C is recommended. At125 °C, dc regulator should run. Basically, it's a dc to dc voltage regulator from the -- series. 1 functions are available in total for the switch converters. We design voltage regulators switchings with 8 pins. The maximum input voltage of dc switcher is 5.5V, so users should limit their voltage accordingly. A 8-MSOP would be the supplier dc dc controller package for this part. Switching controller is necessary to provide a voltage of 5.5V. Voltage 2V is needed for the supply. There will be 100mA current output from the dc switcher above 100mA. The datasheet indicates that the switching converter can output 100V volts at its maximum. A current of 120μA is supplied to it. 3.3V voltage output is lower than 3.3V. Channels are 1 for high-quality communication. In this switching controller, 850 kHz represents the top frequency at which it can switch. Voltage maximum is rated 5.5 V. The nominal current supply of this the controllers dc is 120μA. At 750 kHz, this controller will mostly work as expected.
MCP1651R-E/MS Features
Transistor Driver Outputs
Switching Frequency: 750kHz
Current Limit, Enable, Low Battery, Power Good
PULSE WIDTH MODULATION
Max Duty Cycle: 88 %
Frequency: 750kHz
Switching Frequency: 750 kHz
MCP1651R-E/MS Applications
There are a lot of Microchip Technology
MCP1651R-E/MS DC to DC converter applications.
- Various precision measuring instruments
- Various precision measuring detectors
- Flaw detection equipment
- Balance equipment
- Industrial robots
- Industrial controllers
- Die casting equipment
- Injection molding machinery
- Various CNC machine tools
- Machining centers
You may place an order without registering to VESS Electronics. We strongly recommend that you log in before purchasing as you can track your order at any time.
RFQ (Request for Quotations)It is recommended to send RFQ to get the latest prices and stock availability about the part.Our sales will reply to your inquiry within 24 hours.
Payment MethodFor your convenience, we accept multiple payment methods in USD, Such as:PayPal, Credit Card, and wire transfer.
IMPORTANT NOTICEYou may place an order without registering to 1. You'll receive an order confirmations by e-mail soon . (Please remember to check the spam box if you didn't hear from us). 2. Since stock availability and prices may change at any time, the sales will reconfirm the order details and update you at soonest time.
Most of our products are shipped via FEDEX,DHL,UPS and SF EXPRESS...
Shipping CostShipping Cost starts at $40, but some countries will exceed $40. For example (South Africa, Brazil, India, Pakistan, Israel, etc.).If customer have shipping account, we can make shipment under customer’s shipping account with freight collect directly.
The basic freight (for package ≤0.5 KG ) depends on the time zones and countries
Once the goods are shipped, estimated delivery time depends on the shipping methods you chose. You can track it by the tracking no.
